March, 2018

Internal wall Sealant

   Posted in FAQ, Internal Sealants, Sealants, Stone, water based   

This question was asked by
Vivien Gillies

I have uncovered a stone wall inside my house. The stone needs sealed to stop dust but it is also dull looking. What would be the best product of yours to use? I would prefer a gloss finish to a Matt finish. As it’s an internal wall I understand it needs to be able to breathe or damp becomes an issue. Please can you advise?

For an Internal wall I would recommend using our Water based sealer (link below), it is safe to work with when applying it to a vertical surface and it has very little odour so wont smell the house out.

Water Based Sealer Gloss (WB34)

Drew Palin

Indian Stone Sealer

   Posted in External Sealants, FAQ, Patio, Paving, Sealants, Stone, water based   

This question was asked by
Ian Sutcliffe

l have had a patio laid two years ago with Indian stone and didn’t realise how easily it stained. I am going to clean it this spring and would like to see if l can protect it with a sealer but not darken the colour if possible, could you please advise, approximately 85 square meters area,

As you are looking to keep the paving looking as it does when it is dry I would recommend the Water based Matt sealer (link below) this will have very little effect on the appearance but will offer a good amount of protection for the stone.

Water Based Sealer Matt (WB25)

Drew Palin

Stain or Paint my driveway ?

   Posted in Colouring, Concrete, Driveway, FAQ   

This question was asked by
Ron Turnbull

In April or May I want to paint or stain my driveway which looks bland.
Would take 10 – 12K to replace :-((
The house was built back in 1971 and the driveway is concrete but has a rough “tamped rough finish”.
I hear conflicting info regarding painting or staining the concrete.
Can you advise me – should I paint or stain ?
There are 2 cars sitting on the driveway.
Can you recommend a product of yours that would be best suited and how best to apply it.

I would forget about painting, the paint will start to wear off after a few months.

Staining on the other hand (as long as the prep is done correctly) soaks into the concrete to form a permanent bond.

I would suggest using the Solid colour stain (link below) as this is the quickest and easiest way to brighten up tired looking concrete.

For Prep, mixing and application please review the videos section on the site.

Solid Colour Stain (SOLID)

Drew Palin

concrete staining

   Posted in Colouring, Concrete, FAQ   

This question was asked by
Meriem

I would like to acid stain a concrete floor that has been grounded with 200 grit pads and densified, will the adseals smart color dye work on the concrete?

For the Smartcolour stains to work properly the concrete need to be porous enough for the stain to soak in. Please look at the videos section on www.adsealcolours.co.uk, the last video shows you what you need to look for in regards to the prep.

Drew Palin

Colouring and staining

   Posted in Concrete, FAQ, Sealants   

This question was asked by
Sam Butler

I have recently made a concrete table for use inside. I was looking at possibly using your smart stain to make it a darker shade as it didn’t really come out as dark as I had liked. Wondered what it was like to use on new works. Also was looking at your polyeurethene gloss sealer. Was just looking for some advice really.

Yes the Smart colour will be ok to use and the High gloss PU will give a very nice gloss finish.

In regards to the prep work you will need to acid wash and profile the surface to remove any dusty material from the surface and to increase the porosity (there are a couple of videos on the website to show you what to look for when prepping the surface).

Smart Colour Stain (SMART)

Eco Acid [profiler] (EA)

High-gloss Polyurethane Sealer (HGPU)

Drew Palin